Construction Glossary

A

Aggregate

Crushed stone, gravel, or sand used as a base material in concrete and asphalt mixes, providing bulk and strength.

Air Change

The replacement of the full volume of air in a room or building, usually expressed as air changes per hour (ACH) for ventilation design.

Anchor Bolt

A steel bolt cast into concrete or grouting to fasten structural members like columns, plates, or sill plates to foundations.

Apron

The interior trim board placed beneath a window stool, covering the gap between the wall finish and window frame.

Attic

The unfinished space between the ceiling of the top floor and the underside of the roof, often used for ventilation and insulation.

Awning

A rooflike structure projecting over a window or door, typically canvas or metal, providing shade and weather protection.

Axial Load

A structural load applied along the longitudinal axis of a member, producing either compression or tension through the centerline.

ABS Pipe

Acrylonitrile Butadiene Styrene piping, a rigid black plastic pipe commonly used for drain, waste, and vent systems.

AC (Alternating Current)

Electric current that reverses direction periodically; standard household and commercial electrical supply in the United States.

Access Panel

A removable panel in a wall or ceiling providing entry to plumbing, electrical, or mechanical components for maintenance.

Acoustical Ceiling

A ceiling system using sound-absorbing tiles, typically suspended in a metal grid, to reduce noise and improve acoustic quality.

Adhesive

A bonding agent used to attach two surfaces together by surface attachment and internal strength; includes construction glues and epoxies.

Admixture

A chemical additive introduced to concrete, mortar, or grout to modify properties such as set time, workability, or durability.

Aerator

A threaded fitting on a faucet spout that mixes air with water to reduce splashing and conserve water while maintaining pressure.

AFCI

Arc Fault Circuit Interrupter; a circuit breaker that detects dangerous electrical arcs and shuts off power to prevent fires.

Aggregate Base

A layer of compacted crushed stone or gravel placed beneath concrete slabs, pavements, or foundations to provide a stable subgrade.

Air Barrier

A continuous material or system that restricts airflow through the building envelope, improving energy efficiency and moisture control.

Air Gap

A physical separation between a water supply outlet and a potential source of contamination, preventing backflow into the potable system.

Air Handler

The indoor part of an HVAC system that circulates conditioned air through ductwork using a blower fan and heat exchange coils.

Alcove

A recessed area or nook in a room, often used for built-in shelving, seating, or fixtures like bathtubs and cabinets.

Allowable Load

The maximum load a structural member can safely support as determined by building codes and engineering calculations.

Anchor

A mechanical device embedded in concrete or masonry or driven into framing to secure attachments and resist pull-out forces.

Angle Iron

A structural steel member with an L-shaped cross-section, used for bracing, framing, and supporting masonry or equipment.

Annealed Glass

Standard glass that has been slowly cooled during manufacturing to relieve internal stress; breaks into sharp shards if fractured.

Anode Rod

A sacrificial metal rod inserted into a water heater tank to attract corrosive elements and protect the tank from rusting.

Apron (Window)

The flat trim board attached to the wall below the window stool, running parallel to the floor and finishing the window opening.

Arc Fault

An unintended electrical discharge that can generate extreme heat and ignite nearby combustibles; detected by AFCI breakers.

Architectural Shingle

A premium asphalt roofing shingle with a thickened profile and layered construction, providing enhanced durability and a dimensional appearance.

Area Drain

A floor drain located in a depressed area or exterior paved surface to collect and remove surface water runoff.

As-Built

Drawings or documentation showing the final constructed condition of a project, including all changes made during construction.

Asbestos

A naturally occurring fibrous mineral once widely used for fireproofing and insulation, now heavily regulated due to health hazards from airborne fibers.

Ashlar

Stone masonry made of dressed, squared, and fitted stone blocks laid in regular courses with thin mortar joints.

Asphalt

A dark, viscous petroleum-based binder used in paving, roofing materials, and waterproofing compounds for its adhesive and waterproof qualities.

ASTM

American Society for Testing and Materials; an international standards organization establishing technical standards for materials and testing methods.

Atrium

A large open space, often with a skylight or glass roof, located at the center of a building and extending through multiple floors.

Attic Vent

An opening or device in an attic space that allows moisture and hot air to escape, reducing heat buildup and preventing condensation damage.

Auger

A spiral-shaped drill bit used for boring deep holes in wood or soil; also refers to a device for unclogging drain pipes.

Awl

A pointed hand tool used for marking surfaces, starting screw holes, or piercing small holes in wood, leather, and other materials.

Axe

A chopping tool with a sharp steel head mounted on a handle, used for shaping and cutting wood in rough carpentry and timber framing.

Axial

Pertaining to or aligned with the central axis of a structural member; describes forces applied along the member's centerline.

B

Backfill

Soil or fill material placed against a foundation wall or in a trench around buried structures after construction is complete.

Backflow

The reverse flow of contaminated water into a potable water supply, prevented by air gaps, vacuum breakers, and check valves.

Backsplash

A vertical surface, typically tile or stone, installed behind a countertop or sink to protect the wall from water and food splatter.

Baluster

An individual vertical post or spindle supporting a handrail on a staircase, balcony, or railing system spaced for safety.

Band Joist

The outer floor joist running perpendicular to the main joists around the perimeter of a floor frame, closing off the joist cavities.

Baseboard

A molding strip covering the joint between the interior wall finish and the floor, protecting the wall from scuffs and hiding gaps.

Batten

A narrow strip of wood or material used to cover joints between boards in board-and-batten siding or to secure materials.

Beam

A horizontal structural member designed to support loads across a span, transferring weight to columns, posts, or bearing walls.

Bearing Wall

A wall that supports vertical loads from floors or roofs in addition to its own weight; critical to structural integrity.

Bedding

A layer of sand, mortar, or gravel on which masonry units, pipes, or pavers are laid to provide a level and stable base.

Berm

A raised earthen mound or linear bank of soil used for landscaping, drainage control, or as a visual or noise barrier.

Bevel

An angled cut or edge on a material, not at a right angle, used for fitting, aesthetics, or to eliminate sharp corners.

Bid

A formal price proposal submitted by a contractor or subcontractor for performing specified construction work on a project.

Birdsmouth

A notch cut into the underside of a rafter where it sits atop the top plate of a wall, providing positive bearing and alignment.

Bitumen

A sticky, viscous hydrocarbon material derived from petroleum, used as a binder in asphalt paving and built-up roofing systems.

Blind Nail

A nail driven so its head is hidden, such as in a tongue of tongue-and-groove flooring or behind a shingle tab.

Blocking

Short pieces of framing lumber installed between joists or studs to provide nailing surface, stiffening, or fire-stopping.

Blower Door

A diagnostic tool using a calibrated fan in a doorway to measure the airtightness of a building by pressurization or depressurization.

Blueprint

A traditional term for construction drawings; historically blue-line paper prints, now typically large format digital prints of plans.

Board Foot

A unit of lumber volume equal to a board 12 inches by 12 inches by 1 inch thick; used for pricing and ordering hardwood lumber.

Bond

The pattern in which bricks, blocks, or stones are laid to create structural stability; also the adhesion between materials.

Bottom Plate

The lowest horizontal member of a framed wall, resting on the floor or foundation, to which vertical studs are attached.

Bracing

Temporary or permanent structural members installed diagonally or laterally to resist wind, seismic, or buckling forces.

Brick

A rectangular fired clay or concrete masonry unit used for walls, pavements, and facades in residential and commercial construction.

Bridging

Cross bracing or solid blocking installed between floor joists at mid-span to distribute loads and prevent joist twisting.

BTU

British Thermal Unit; the amount of heat needed to raise one pound of water by one degree Fahrenheit, used to rate heating and cooling capacity.

Building Code

A set of regulations adopted by a jurisdiction governing the design, construction, and occupancy of buildings to ensure safety.

Building Envelope

The physical barrier separating the interior conditioned space from the exterior environment, including walls, roof, foundation, windows, and doors.

Built-Up Roof

A multi-layer roofing system of alternating bitumen and felts, topped with aggregate, providing a durable waterproof membrane for flat roofs.

Bullnose

A rounded edge on trim, tile, stair treads, or drywall corners, eliminating sharp angles for a softer appearance and safety.

Burl

An irregular growth on a tree producing highly figured wood grain, prized for veneer and decorative woodworking applications.

Butt Joint

A simple joint where two pieces of material meet end-to-end or edge-to-edge without overlapping, fastened with nails, screws, or adhesive.

Butterfly Roof

An inverted roof form with two surfaces sloping downward toward a central valley, resembling the wings of a butterfly.

BX Cable

A type of armored electrical cable with a flexible metal sheathing enclosing insulated conductors, used before Romex became widespread.

Bypass Door

A sliding door system where panels slide past each other on parallel tracks, commonly used for closets and patio doors.

C

Cantilever

A structural element extending horizontally beyond its support, anchored at one end while carrying loads on the projecting portion.

Cap

The top protective layer of a wall, chimney, or post, often sloped to shed water and prevent moisture intrusion into the structure.

Capillary Action

The movement of moisture through small pores or cracks against gravity, drawing water upward through materials by surface tension.

Casing

Trim molding installed around door and window openings, covering the gap between the frame and the surrounding wall finish.

Cast Iron

A dense, durable iron alloy with high carbon content, poured into molds and used for drain pipes, radiators, and heavy-duty fittings.

Caulk

A flexible sealant applied along joints and gaps to seal out air, moisture, and insects, allowing for minor material movement.

Cavity Wall

A masonry wall constructed with two separated layers (wythes) tied together, leaving a continuous air space for drainage and insulation.

CCA

Chromated Copper Arsenate; a wood preservative historically used for pressure treating lumber, phased out for most residential uses due to toxicity.

Ceiling Joist

A horizontal framing member supporting a ceiling surface and transferring roof loads to the bearing walls; may also serve as rafter ties.

Cement

A fine gray powder, typically Portland cement, that chemically reacts with water to bind aggregates together and form concrete or mortar.

CFM

Cubic Feet per Minute; a unit measuring airflow volume, used to rate exhaust fans, ventilation systems, and HVAC equipment capacity.

Chair Rail

A horizontal molding installed on interior walls at approximately chair-back height, primarily decorative but also protecting walls from furniture.

Chase

A vertical or horizontal framed enclosure through a building, used to conceal ductwork, plumbing, wiring, or chimneys between floors.

Chimney

A vertical masonry or metal structure containing one or more flues for exhausting combustion gases from fireplaces, furnaces, or water heaters.

Circuit Breaker

An automatic electrical switch in a panel that interrupts current flow when overcurrent or short circuit conditions are detected.

Cladding

The exterior surface material of a building envelope, such as siding, brick veneer, or metal panels, providing weather protection and aesthetics.

Cleanout

A plugged access fitting in a drainage pipe providing an entry point for a snake or auger to clear blockages in the piping.

Clear Span

The unobstructed distance between two structural supports without intermediate columns or bearing walls, allowing open floor plans.

Cleat

A small strip of wood or metal attached to a surface as a support or fastener to secure shelving, cabinets, or roof panels.

CMU

Concrete Masonry Unit; a standardized hollow concrete block used for load-bearing and non-load-bearing walls, typically 8"x8"x16" nominal.

CO Detector

Carbon Monoxide Detector; a safety device that sounds an alarm when dangerous levels of odorless, colorless carbon monoxide gas accumulate.

Code

The legally adopted set of regulations dictating minimum construction standards for structural safety, fire protection, energy, and other aspects.

Coffered Ceiling

A ceiling with recessed panels formed by intersecting beams, creating a grid pattern; adds architectural depth and visual interest.

Cold Joint

The interface between consecutive concrete pours where the previous pour has already hardened, creating a potential weakness if not properly treated.

Collar Tie

A horizontal framing member connecting opposing rafters in the upper third of a roof, resisting outward thrust at the ridge.

Column

A vertical structural member primarily subjected to compressive loads, transferring weight from beams or slabs to the foundation below.

Combustion Air

Air supplied to a fuel-burning appliance to support complete combustion and safe venting of exhaust gases, required by code.

Compaction

The mechanical process of densifying soil or fill material using rollers, tampers, or vibratory compactors to improve bearing capacity.

Composite

A material made from two or more constituent materials with different properties, combined to produce enhanced structural characteristics.

Compression

A force that pushes or presses a material together, shortening it; the opposite of tension. A fundamental structural stress type.

Concrete

A composite material of cement, aggregate, and water that hardens through hydration into a stone-like mass for structural applications.

Condensate

Water formed when warm, moisture-laden air contacts a cold surface and humidity condenses into liquid; must be drained from HVAC equipment.

Conduction

The transfer of heat through a solid material by molecular vibration without bulk movement of the material; one of three heat transfer modes.

Conduit

A metal or plastic tube or channel that protects and routes electrical wiring through a building, from panel to outlets and fixtures.

Construction Joint

A planned interface between two adjacent concrete placements, designed to allow movement or to separate a pour into manageable sections.

Control Joint

A deliberately weakened linear groove in a concrete slab or wall that controls the location of cracking from drying shrinkage.

Convection

Heat transfer through the movement of fluids or gases, such as warm air rising or water circulating, used in heating and cooling systems.

Coping

A protective cap at the top of a wall, parapet, or chimney, typically sloped or projecting to direct water away from the masonry below.

Corbel

A stepped projection of masonry courses extending outward from a wall surface, supporting an overhanging load or providing decorative effect.

Corner Bead

A metal or vinyl strip applied to external drywall corners before finishing, providing a straight, durable, impact-resistant edge.

Cornice

A decorative horizontal projection at the top of a wall or along the roofline, consisting of moldings and trim that crown the building.

Counterflashing

A vertical metal flashing secured into a wall slot and folded down over the top of base flashing to create a waterproof roofing junction.

Course

A continuous horizontal layer of masonry units such as bricks, blocks, or stones laid in a single level of a wall.

Cove

A concave molding or curved joining surface at the junction between ceiling and wall, or a recessed area in a ceiling for indirect lighting.

Crawl Space

An accessible, shallow, unfinished space between the ground and the first floor of a building, used for access to utilities beneath.

D

Dado

A rectangular groove cut across the grain of a board, used in joinery to accept the edge of another board for cabinets and shelving.

Dampproofing

A coating applied to foundation walls to resist the passage of moisture in vapor form, less robust than full waterproofing.

Dead Load

The permanent static weight of a building including all structural elements, fixed finishes, and permanently attached equipment.

Decking

Structural sheathing material attached to roof or floor framing; also refers to the finished surface boards of an outdoor deck.

Deflection

The amount a structural member bends or displaces under an applied load; limited by building codes to prevent damage and discomfort.

Demising Wall

A fire-rated wall dividing adjacent units in a multi-unit building, extending from slab to underside of floor above, separating tenants.

Dew Point

The temperature at which air becomes saturated with moisture and water vapor begins to condense into liquid; critical for condensation control.

Dimension Lumber

Sawn lumber cut to standardized widths and depths, such as 2x4, 2x6, or 2x10, primarily used for structural framing.

Direct Vent

A sealed combustion system drawing outside air directly into a fuel-burning appliance and exhausting gases through a coaxial vent.

Door Jamb

The vertical side members of a door frame forming the opening and providing the mounting surface for hinges and strike plates.

Dormer

A vertical window projection built through the sloping plane of a roof, adding headroom, daylight, and architectural character to upper floors.

Double-Hung

A window with two operable sashes, one upper and one lower, sliding vertically within the frame for ventilation from top or bottom.

Downspout

A vertical pipe attached to a gutter system that carries collected roof water down to ground level or into a drainage system.

Drain Tile

Perforated pipe installed in a gravel bed below grade around a foundation to collect and redirect ground water, preventing basement flooding.

Drip Edge

A metal flashing installed along roof edges, designed to direct water runoff into the gutter and away from the fascia and building.

Dry-In

The stage of construction when the roof covering, weather barrier, windows, and doors are installed, making the interior weathertight.

Drywall

A rigid interior wall and ceiling finish material made of a gypsum plaster core sandwiched between paper facings, also called gypsum board or sheetrock.

Duct

A sheet metal, fiberglass, or flexible tube used to distribute conditioned air from HVAC equipment to rooms and return air for recirculation.

DWV

Drain, Waste, and Vent; the plumbing system carrying wastewater and sewage from fixtures to the sewer while venting sewer gases.

Dye Lot

A batch of material, such as carpet or tile, produced in the same dye run to ensure color consistency; different lots may vary slightly.

Deadbolt

A door lock with a solid rectangular bolt that slides into a strike plate, operated by key or thumb turn for enhanced security.

Diagonal Bracing

Structural members installed at an angle to the vertical plane to resist lateral forces such as wind and seismic loads on framed walls.

Diaphragm

A horizontal structural element, such as a floor or roof deck, that transfers lateral forces to vertical shear-resisting elements.

Dimension

The exact or nominal measurements of a building component, material, or space, specifying length, width, height, and thickness.

Distributor

A device or component that divides and channels air, water, or other materials to multiple outlets in a building system.

Diverter

A plumbing valve that redirects water flow from one outlet to another, such as from a tub spout to a shower head.

Dovetail

A woodworking joint featuring interlocking fan-shaped pins and tails, providing exceptional strength in drawer and box construction.

Dowel

A cylindrical wooden or metal pin inserted into corresponding holes in two pieces of material to align or join them together.

Downlight

A recessed light fixture mounted flush in a ceiling, directing illumination downward; also called a can light or pot light.

Draft Stop

A material or assembly installed in concealed spaces such as soffits and dropped ceilings to limit the passage of air and fire spread.

Drain

A pipe or channel that carries liquid waste or storm water by gravity from fixtures or surfaces to the sewer or disposal system.

Drawer

A sliding storage compartment built into cabinetry, composed of a front, sides, back, and bottom, sliding on guides or runners.

Dressed Lumber

Lumber that has been planed smooth on one or more sides to a uniform thickness and width after initial rough sawing.

Drip

A molded projection at the bottom of exterior trim that directs water away from the wall surface, preventing moisture accumulation.

Dry Rot

Timber decay caused by certain fungi that consume cellulose in wood, leaving it brittle, shriveled, and structurally compromised.

E

Eave

The lower edge of a roof projecting beyond the exterior wall, providing shade and directing rain water away from the building.

EER

Energy Efficiency Ratio; a measure of cooling output divided by electrical input for air conditioners at a specific outdoor temperature.

Efflorescence

A white powdery deposit of soluble salts on the surface of masonry or concrete, caused by water migrating through and evaporating.

Egress

A path of exit for occupants from a building to safety; building codes specify minimum egress window sizes for sleeping rooms.

Elastomeric

A coating material with rubber-like elastic properties that stretches and returns to its original shape, used for waterproofing and crack bridging.

Elbow

A pipe fitting allowing a change in direction, typically at 45 or 90 degrees, used in plumbing, conduit, and ductwork installations.

Electrical Panel

The main distribution point for a building's electrical circuits, containing circuit breakers or fuses that protect each branch circuit.

Elevation

An orthographic drawing showing the exterior face of a building; also refers to the height of a point above a reference datum.

End Grain

The exposed face of a board cut across the growth rings; absorbs moisture more readily than face or edge grain and requires sealing.

Energy Star

A government-backed program certifying appliances, windows, and building practices that meet superior energy efficiency standards.

Engineered Wood

Structural wood products manufactured by binding wood strands, veneers, or fibers with adhesives, including LVL, OSB, and plywood.

Epoxy

A two-part thermosetting resin adhesive known for extremely high bonding strength, chemical resistance, and gap-filling properties.

Escutcheon

A decorative protective plate or flange surrounding a plumbing pipe, valve, or keyhole on a finished surface, covering the wall opening.

Estimate

A calculated approximation of the cost of materials, labor, and equipment required to complete a construction project.

Evaporator

The indoor coil in an air conditioning system where liquid refrigerant absorbs heat from interior air as it evaporates into a gas.

Excavation

The process of removing earth for foundations, basements, trenches, or grading; the first major sitework activity in construction.

Expansion Joint

A gap or flexible material installed between building elements to accommodate thermal expansion and contraction without causing damage.

Expansion Tank

A small pressurized tank connected to a water heating system, absorbing the increase in water volume as it heats to prevent pressure buildup.

Exposure

The portion of a roofing shingle or tile that is visible to the weather after installation; the exposed tab or surface area.

Eave Vent

An intake vent located in the soffit or eave area that allows fresh outside air to enter the attic space as part of balanced ventilation.

Edge Banding

A thin strip of veneer, PVC, or wood applied to the exposed edges of plywood or composite panels for appearance and protection.

Edge Grain

Lumber sawn with growth rings running roughly perpendicular to the wide face, resulting is stable, vertical grain with minimal cupping.

Effluent

Liquid waste discharged from a septic tank into a leach field for further treatment and absorption into the surrounding soil.

EIFS

Exterior Insulation and Finish System; a synthetic stucco cladding system with foam insulation board and a textured finish coat applied over it.

Elbow Catch

A cabinet door latch that secures when the door is pushed closed and releases with a push or pull, often used on cabinet pairs.

Electric Strike

An electronically controlled door strike plate allowing a door to be locked or unlocked remotely, used in access control and intercom systems.

EMT

Electrical Metallic Tubing; thin-wall, unthreaded steel conduit used to protect and route electrical wiring in exposed and concealed locations.

Enamel

A hard, glossy paint finish that dries to a smooth, durable coating, often used on trim, cabinets, and high-touch surfaces.

End Cap

A fitting that seals the open end of a pipe or duct, preventing leaks and protecting the interior from debris and pests.

Exhaust Fan

A mechanical ventilation fan that removes stale air, moisture, and odors from a room and exhausts it to the outdoors through ductwork.

F

Face Brick

High-quality brick with a finished surface intended for exposed wall applications where appearance is important.

Fall

The slope or gradient of a drainage pipe, surface, or gutter designed to allow water to flow by gravity; typically expressed as inches per foot.

Fascia

The vertical board nailed to the ends of rafters or trusses at the eave line, supporting the gutter and providing a finished roofline edge.

Fastener

A mechanical device such as a nail, screw, bolt, or staple used to join two or more building components securely together.

Felt Paper

Asphalt-saturated heavy paper used as an underlayment beneath roofing and siding to provide secondary water protection.

Fender Washer

An oversized thin washer with a small center hole, used to distribute the clamping force of a fastener over a larger surface area.

Fenestration

The arrangement, design, and placement of windows, doors, skylights, and other openings in the exterior envelope of a building.

Fiber Cement

A composite siding material made of cement, sand, and cellulose fibers; durable, fire-resistant, and dimensionally stable exterior cladding.

Field Stone

Naturally rounded or irregular stones gathered from fields or the ground surface, used for rustic walls, veneers, and landscaping.

Filler

A material used to level imperfections, fill nail holes, gouges, or cracks in wood, drywall, or other surfaces before painting or finishing.

Finish Carpentry

The final phase of woodwork including installation of trim, moldings, doors, cabinets, and built-ins requiring precise fit and appearance.

Fire Block

A material or assembly installed in concealed spaces to block the vertical passage of fire and smoke within walls, floors, and chases.

Fire Rated

A classification indicating a building assembly has been tested to resist fire spread for a specified period of time, such as 1 hour or 2 hours.

Fish Tape

A flexible, flat steel or fiberglass tape used by electricians to pull wire through conduit, wall cavities, and other enclosed spaces.

Fixture

A permanently attached plumbing, electrical, or lighting device such as a sink, toilet, ceiling light, or sconce in a building.

Flagstone

Flat, thin, irregularly shaped natural stone pieces used for paving patios, walkways, and stepping paths with a rustic appearance.

Flange

A projecting rim or collar on a pipe, beam, or component used for attachment, strengthening, or connecting to another element.

Flashing

Thin metal or membrane material installed at roof intersections, valleys, chimneys, and window tops to direct water and prevent leaks.

Flat Grain

Lumber sawn with growth rings roughly parallel to the wide face; more prone to cupping but more economical than edge grain.

Flex Duct

Flexible insulated ductwork with a wire coil core wrapped in plastic and insulation, used to connect HVAC supply air to registers.

Float Glass

Sheet glass manufactured by floating molten glass on a bed of molten tin, producing a uniform thickness with smooth parallel surfaces.

Floor Joist

A horizontal framing member supporting floor loads between bearing walls, beams, or girders, typically spaced 16 or 24 inches on center.

Flue

A passage inside a chimney, vent, or pipe through which combustion gases, smoke, and heat travel upward and out of the building.

Flush

Aligning two surfaces so they are perfectly level and even with each other, without any projection or recess between the adjoining elements.

Flux

A chemical compound applied to metal before soldering that cleans the surface, prevents oxidation, and promotes uniform solder flow.

Footing

The widened base of a foundation wall or column that distributes building loads over a greater soil area to prevent settling.

Form

A temporary wooden or metal mold into which concrete is placed and held until it hardens, gaining the desired shape and dimensions.

Foundation

The lowest load-bearing part of a building, typically below grade, that transfers structural loads into the ground; includes footings and walls.

Framing

The skeletal structure of a building composed of studs, joists, rafters, and beams that forms the shape and supports all finishes.

French Drain

A gravel-filled trench containing a perforated pipe that redirects surface water and groundwater away from foundations or landscape areas.

Frost Line

The maximum depth below grade at which soil freezes in winter; footings must extend below this line to prevent frost heave damage.

Furring

Thin strips of wood or metal attached to a wall or ceiling surface to create a level nailing surface or provide an airspace behind finishes.

Fuse

A safety device containing a metal strip that melts when excessive current flows, breaking the circuit; an older form of overcurrent protection.

F-Clamp

A clamp shaped like the letter F with a sliding lower jaw, used to hold workpieces together during drilling, gluing, or assembly.

G

Gable

The triangular upper portion of an exterior wall between the edges of a sloping roof, enclosing the end of the roof ridge.

Gable Vent

A louvered vent installed in a gable end to allow passive air circulation through the attic space, reducing heat and moisture buildup.

Galvanized

Steel coated with a protective layer of zinc through hot-dipping or electroplating to resist rust and corrosion in exposed applications.

Gambrel Roof

A double-sloped roof with a steeper lower pitch and shallower upper pitch on each side, providing extra upper floor headroom in barn-style designs.

Gauge

A measurement of sheet metal thickness, wire diameter, or the distance between nails in a nail gun; a lower gauge number indicates thicker material.

GFCI

Ground Fault Circuit Interrupter; a fast-acting receptacle or breaker that shuts off power when current leakage to ground is detected, preventing shock.

Girder

A large horizontal structural beam, often steel or built-up wood, supporting floor joists, walls, or concentrated loads and transferring them to columns.

Glazing

Glass installed in windows, doors, or curtain wall systems; also the process of installing glass panes into frames with putty or gaskets.

Glulam

Glued Laminated Timber; an engineered wood beam made by bonding together layers of dimension lumber with durable moisture-resistant adhesives.

Grade

The elevation of the ground surface around a building; also the classification of lumber quality, or the slope of a drainage surface.

Grade Beam

A reinforced concrete beam at ground level spanning between piers or piles, supporting wall loads above and transferring them to deep foundations.

Grain

The orientation, size, and pattern of wood fibers determined by growth rings; affects strength, workability, and appearance of lumber.

Green Lumber

Freshly sawn lumber with a moisture content above 19%, not yet dried or seasoned; prone to shrinkage, twisting, and checking as it dries.

Ground

A conducting connection between an electrical circuit and the earth, providing a safe path for fault current to prevent shocks and fires.

Ground Fault

An unintentional electrical connection between an energized conductor and a grounded surface, creating a shock hazard detected by GFCI devices.

Grout

A fluid mixture of cement, sand, and water used to fill joints between tiles, bond reinforcing steel in masonry, or fill cavities in concrete.

Gusset

A flat plate, usually metal or plywood, fastened across a joint to strengthen and stiffen the connection between framing members at a truss node.

Gutter

A horizontal channel attached to the eave of a roof that collects rain runoff and directs it to downspouts, protecting the foundation from water.

Gypsum

A soft sulfate mineral used as the primary core material in drywall panels, valued for its fire-resistant and sound-dampening properties.

Gable End

The vertical wall at the end of a gable roof from the eave to the peak; requires proper bracing due to large wind load exposure.

Galvanic Corrosion

Electrochemical deterioration occurring when two dissimilar metals in contact with an electrolyte, such as water, create a low-energy corrosion cell.

Gang Nail

A metal connector plate with many small teeth punched from the plate, pressed into adjacent wood members to fasten truss joints quickly.

Gasket

A compressible sealing material placed between two mating surfaces to prevent the passage of fluid, air, or gas at the joint.

GFI

Ground Fault Interrupter; an alternate term for GFCI, referring to the same safety device that trips when detecting current leakage to ground.

Glue Block

A small block of wood adhesively attached at an interior corner joint to reinforce the connection, commonly used in cabinet and furniture construction.

H

Habitat

The natural environment where an organism lives; in construction, sensitivity to habitat affects site development and environmental permitting.

Hairline Crack

A very fine, narrow crack in concrete, plaster, or drywall, typically less than 1/16 inch wide, often caused by minor shrinkage or settlement.

Half Wall

A partial-height wall, typically extending 36-42 inches from the floor, used to define spaces visually without fully enclosing them; also called a pony wall.

Hammer

A hand tool with a weighted head on a handle, used to drive nails, break materials, or shape metal; available in many configurations for specific tasks.

Handrail

A continuous rail mounted on brackets alongside stairs or ramps, graspable for balance and support; required by code within specific height ranges.

Hanger

A metal connector, such as a joist hanger or pipe hanger, used to support framing members, pipes, or ductwork from a structural element.

Hardboard

A dense, panel material made from compressed wood fibers and resin, used for siding, underlayment, and furniture backing; also called Masonite.

Hardwood

Wood from deciduous, broadleaf trees such as oak, maple, and cherry; generally denser and more durable than softwood, used for flooring and cabinetry.

Header

A horizontal structural beam placed above a door, window, or other opening in a wall to carry loads around the opening to adjacent studs.

Hearth

The fireproof floor area directly in front of a fireplace, extending into the room; protects combustible flooring from sparks and heat.

Heat Pump

An HVAC device that moves heat between indoors and outdoors using refrigerant and a compressor, providing both heating in winter and cooling in summer.

Heel

The lowest point of a roof truss or rafter where it meets the top plate of the exterior wall; critical for bearing and load transfer.

Hip Roof

A roof with slopes on all four sides where each wall face meets a sloped roof plane, providing excellent wind resistance and shedding.

Hold-Down

A metal connector anchoring a wall or post to the foundation or framing below, resisting uplift forces from wind or seismic events.

Honeycomb

A surface defect in poured concrete where aggregate is visible and mortar is missing, typically caused by poor consolidation or stiff mix designs.

Hopper

A large funnel-shaped container or bin used to temporarily store and meter bulk materials like sand, cement, or aggregate for batching systems.

Hose Bib

An outdoor water faucet with a threaded spout for attaching a garden hose; also called a sillcock, typically having an anti-siphon feature.

Hot Wire

The current-carrying conductor in a circuit that is energized; the wire that carries voltage from the source to the load, typically black or red.

Housewrap

A synthetic weather-resistant barrier wrapped around the exterior sheathing to block liquid water while allowing vapor to escape, like Tyvek.

HVAC

Heating, Ventilation, and Air Conditioning; the integrated mechanical systems controlling indoor temperature, humidity, and air quality in a building.

Hydronic

A heating or cooling system that uses circulating water or water-glycol solution as the heat transfer medium through pipes and radiators or coils.

Hygrometer

An instrument for measuring the relative humidity of air or soil, used to monitor moisture conditions that affect building materials and comfort.

Habitable Space

A room or area within a building intended for living, sleeping, eating, or cooking; must meet code requirements for light, ventilation, and egress.

Half-Lap

A wood joint where half the thickness of each member is removed so they overlap flush, providing a strong glued connection with increased surface area.

Hand Plane

A hand tool with a sharp blade that shaves thin layers of wood to smooth, flatten, or reduce the thickness of lumber in finish carpentry.

Hardpan

A dense, compacted layer of soil that restricts root growth and water penetration; encountered during excavation and may require special equipment.

Haunch

An increased depth or thickness at the support point of a beam or rafter where bending forces are greatest, improving structural capacity.

Header Course

A row of bricks laid with their short end facing outward in a masonry wall, used to bond wythes together in solid brick construction.

HEPA

High Efficiency Particulate Air; a filter classification capable of capturing 99.97% of particles 0.3 microns, used for cleanroom and remediation work.

Hold-Down Anchor

A heavy-duty metal connector strapping or bolting a wall to the foundation or lower wall, engineered to resist uplift and overturning forces.

I

I-Beam

A structural steel beam with an I-shaped cross-section having wider flanges and a narrower web, efficiently resisting bending and shear.

Ice Dam

A ridge of ice at a roof eave that blocks meltwater, forcing it under shingles and causing interior leaks in cold climates.

IIC

Impact Insulation Class; a rating measuring how well a floor-ceiling assembly reduces impact sound transmission such as footsteps or dropped objects.

Impact Driver

A power tool that delivers strong rotational impacts in addition to rotation, ideal for driving long screws and lag bolts with less effort.

Incandescent

A type of light bulb producing light by heating a filament wire until it glows; being phased out in favor of more efficient LED and CFL alternatives.

Infill

Material placed to fill a void, such as insulation in a stud cavity, panels between structural members, or new construction in an existing urban lot.

Inlet

An opening or intake through which air, water, or other fluid enters a system, duct, drain, or device for processing or distribution.

Insulation

Material with high thermal resistance installed in the building envelope to slow heat transfer, reduce energy costs, and maintain indoor comfort.

Interceptor

A plumbing device that captures and retains undesirable materials such as grease, oil, or solids before they enter the drainage system.

Interior Finish

The final exposed surface materials inside a building, including drywall, paint, flooring, trim, and cabinetry that define the interior appearance.

IRC

International Residential Code; a model building code governing the construction and alteration of one- and two-family dwellings and townhouses.

Isolation Valve

A manual shut-off valve on a supply line allowing a single fixture or appliance to be isolated without shutting off water to the entire building.

I-Joist

An engineered wood floor joist with a thin OSB web between solid lumber flanges, providing long spans, light weight, and dimensional stability.

Ice Barrier

A self-adhering waterproof membrane applied along eaves in cold climates, extending up past the interior wall line to prevent ice dam leakage.

Impact Wrench

A power tool delivering high torque bursts to tighten or loosen nuts and bolts rapidly, used in steel erection, mechanical, and automotive work.

Incising

Small slits pressed into wood surfaces before pressure treating to improve preservative penetration, typically used on difficult-to-treat species.

Infiltration

Uncontrolled leakage of outdoor air into a building through cracks, joints, and openings in the envelope, affecting energy efficiency and comfort.

Inlay

A decorative technique where contrasting material is set flush into a recessed cavity in the surface of another material, such as wood or stone in flooring.

Interlock

A mechanical or electrical arrangement where one component prevents another from operating out of sequence, used for safety and proper system function.

Irrigation

A system of pipes, valves, and sprinkler heads that artificially distributes water to landscaping; may include timers and rain sensors for efficiency.

J

Jack Rafter

A shortened rafter framing between a hip rafter and the wall top plate or between a valley rafter and the ridge in a roof system.

Jack Stud

A shortened vertical stud placed under each end of a header to support the header and transfer loads down to the bottom plate or foundation.

Jamb

The vertical side members forming the inner sides of a door or window frame opening, against which the door or sash closes.

Joint

The intersection or connection point where two or more building materials, components, or structural members meet and are secured together.

Joint Compound

A gypsum-based paste applied to drywall seams, corners, and fastener heads, then sanded smooth to create a seamless wall surface; also called mud.

Joist

A horizontal structural framing member, typically wood or steel, supporting a floor or ceiling load across its span between bearing supports.

Joist Hanger

A U-shaped metal connector nailed to a ledger or beam to support the end of a joist, providing positive bearing and preventing rotation.

Junction Box

An enclosed metal or plastic box where electrical conductors are spliced or terminated, providing protection and accessibility for connections.

J-Channel

A J-shaped trim piece used around windows, doors, and edges of vinyl or metal siding panels to receive and conceal the cut ends of siding.

Jack Post

An adjustable steel column, typically with a threaded top, used to provide temporary or permanent support for beams, girders, or sagging floors.

Jalousie

A window composed of multiple horizontal glass slats that pivot in unison for ventilation; popular in mid-century and tropical architecture.

Jig

A custom-made or adjustable device that guides tools or holds workpieces in a fixed position for repetitive, precise machining or assembly operations.

Job Site

The physical location where construction activities are performed; includes the building footprint, staging areas, material storage, and access routes.

Joggle

A small offset or step formed in adjacent materials so they interlock, as in sheet metal flashing or sections of concrete formwork at construction joints.

Journeyman

A skilled tradesperson who has completed an apprenticeship program and is qualified to work independently in their craft under a license or card.

K

K-Style Gutter

The most common residential gutter profile, with a flat back and decorative front shaped like crown molding; holds more water than half-round gutters.

KD (Kiln Dried)

Lumber that has been dried in a controlled kiln to reduce moisture content to a specified level, minimizing shrinkage, warping, and checking after installation.

Kerf

The width of material removed by a saw blade cut; the slot or groove remaining after a saw passes through the material.

Key

A mechanical or physical interlock between two surfaces; also a roughened or grooved surface that improves mechanical bond, or a wedge for locking.

Keyway

A groove or slot cut into the top of a concrete footing to receive the first course of foundation wall, locking them together against lateral movement.

Kick Plate

A protective metal or plastic plate attached to the bottom of a door to prevent damage and scuffing from foot traffic, carts, or cleaning equipment.

Kiln

A heated chamber for drying lumber, firing bricks and ceramics, curing coatings, or heat-treating materials under controlled temperature and humidity.

King Stud

The full-length vertical stud running continuously from top plate to bottom plate adjacent to an opening, flanking the jack studs and header.

Kip

A unit of force equal to 1,000 pounds; commonly used in structural engineering to express large loads, reactions, and member capacities conveniently.

Knee Brace

A diagonal bracing member connecting a post and beam or a column and truss, providing lateral stability by triangulating the corner connection.

Knockdown Texture

A drywall finish achieved by spraying thinned joint compound onto a ceiling or wall and lightly scraping it flat before drying, creating a mottled pattern.

Knot

The cross-section of a branch embedded in a tree trunk, appearing in lumber as a circular or oval feature; affects strength, drying, and appearance.

Kraft Paper

A strong brown paper used as a vapor retarder facer on fiberglass insulation batts, installed with the paper facing the warm-in-winter side.

K-Brace

A structural bracing configuration where diagonal members form a K-shape between vertical columns and horizontal beams to transfer lateral loads.

Keeper

The metal plate on a door jamb that receives the latch bolt or deadbolt when the door is closed; also called a strike plate.

L

Lag Bolt

A heavy-duty fastener with a hex head and coarse wood threads, driven with a wrench to secure heavy timbers, ledgers, and structural connections.

Laminate

A product made by bonding together multiple thin layers of material; includes plastic laminate countertops, laminated veneer lumber, and flooring planks.

Laminated Glass

Safety glass composed of two or more panes bonded with a tough plastic interlayer that holds fragments if broken, used in windshields and security glazing.

Landing

A level platform at the top, bottom, or between flights of stairs, providing a resting point and meeting code requirements for maximum stair rise.

Lap Joint

A joint where two members overlap each other, with material removed from each so the outer surfaces sit flush, increasing gluing surface and strength.

Lath

A framework of wood or metal strips attached to framing to support plaster; now typically expanded metal lath for plaster and stucco applications.

Lattice

Crisscrossed strips of wood, vinyl, or metal forming a decorative open framework, used under porches, decks, and as privacy screening.

Laying Length

The face-to-face dimension of a pipe fitting, valve, or plumbing fixture measured between inlet and outlet connection points.

Leach Field

An underground system of perforated pipes in gravel-filled trenches that disperses effluent from a septic tank into soil for natural treatment; also called drain field.

Ledger

A horizontal board or beam attached to a vertical surface, such as the board bolted to a house wall from which deck joists are hung.

Level

A tool with bubble vials used to establish true horizontal and vertical planes; also the condition of being perfectly horizontal or at a uniform elevation.

Lien

A legal claim against a property by unpaid contractors, subcontractors, or suppliers; a mechanic's lien secures payment for labor and materials furnished.

Light

An individual pane of glass in a divided glazing system; also the visible section of a window, particularly in multi-pane or muntin-bar configurations.

Limit Switch

A safety control in an HVAC system that shuts off the burner or heating element if the heat exchanger or plenum temperature exceeds a safe limit.

Linear Foot

A unit of measurement of length along a straight line, irrespective of width or thickness; used for pricing trim, lumber, and piping sold by the running foot.

Lintel

A horizontal structural beam spanning the top of a wall opening such as a window or door, supporting the load of the wall above; may be steel, concrete, or stone.

Live Load

Temporary or movable loads on a structure, including occupants, furniture, snow, and equipment; distinct from the permanent dead load in design.

Load Bearing

Describes any structural element that carries weight from above and transfers it to the supporting elements below; removal requires engineering analysis.

Lock Set

A complete door locking assembly including the handle, latch mechanism, strike plate, and all associated mounting hardware sold as a unit.

Lookout

A short horizontal framing member cantilevered from the last rafter or truss to support the overhanging soffit at the gable end of a roof.

Louver

A slatted opening for ventilation that allows air passage while blocking rain, sight lines, and direct sunlight; installed in walls, doors, and gables.

Lumber

Wood that has been sawn from logs into standardized sizes for construction; classified by species, grade, and moisture content at time of manufacture.

LVL

Laminated Veneer Lumber; an engineered wood beam made from thin veneers bonded under heat and pressure, used for headers, beams, and rim boards.

Lag Screw

A heavy-duty wood screw with a square or hex head, coarse threads, and a sharp point, tightened with a wrench rather than a screwdriver.

Laminate Beam

A structural beam constructed by gluing together multiple layers of solid lumber or veneers for increased strength and span capability.

Landing Newel

A vertical post at a stair landing that supports the handrail and balustrade where the stair changes direction or at the termination point.

Lap Siding

Horizontal boards installed from the bottom up with each course overlapping the one below, shedding water from the wall; includes clapboard and bevel siding.

Lateral Load

A horizontal force acting on a structure, such as wind pressure or seismic ground motion, resisted by shear walls, bracing, and diaphragms.

Lean-to

A simple shed structure with a single-slope roof attached to a larger existing building, using the wall of the main structure as one side of support.

Light Gauge

Thin cold-formed steel framing members used for non-load-bearing interior walls and some structural applications; lighter than structural steel shapes.

M

Mantel

A shelf or decorative framing piece mounted above a fireplace opening, often used for displaying objects but also serving as a heat deflector.

Mantle

An alternate spelling for mantel; also in geology, the layer of the earth between the crust and core, not typically a construction term.

Manufactured Home

A dwelling built entirely in a factory on a permanent steel chassis and transported to the site; formerly called mobile homes, built to HUD code.

Masonry

Building construction using individual units of brick, stone, concrete block, or similar materials laid in mortar to form walls and structures.

Mastic

A thick, pasty adhesive used for bonding tiles, panels, and trim; remains flexible after curing and is applied with a notched trowel.

MDF

Medium Density Fiberboard; an engineered wood panel made of fine wood fibers and resin under heat and pressure, with a smooth, uniform surface for painting.

Mechanical Room

A dedicated room or space in a building housing the HVAC equipment, water heater, electrical panels, and other major mechanical systems.

Membrane

A thin, flexible layer of material that serves as a barrier against water, vapor, air, or sound transmission in the building envelope.

MEP

Mechanical, Electrical, and Plumbing; the three primary building systems that provide environmental comfort, power, lighting, and water services in a building.

Metal Lath

Expanded metal mesh attached to framing as a substrate for plaster or stucco finishes, providing mechanical keying and crack resistance.

Meter Base

The weatherproof enclosure mounted on the exterior of a building that houses the electric utility meter and provides connection points for service conductors.

Millwork

Factory-manufactured wood products including doors, window frames, trim, moldings, stair parts, and cabinetry components produced in a woodworking mill.

Miter

A joint made by cutting two pieces of material at equal angles, typically 45 degrees, so the joined pieces form a precise 90-degree corner.

Modular

A construction method using factory-built sections or modules shipped to the site and assembled on a permanent foundation; distinct from manufactured housing.

Moisture Barrier

A material or coating that resists the passage of liquid water through building assemblies, protecting structural components from moisture damage.

Monkey Wrench

An adjustable wrench with smooth, parallel jaws used primarily for gripping and turning pipes and large nuts in plumbing and mechanical work.

Monolithic

Constructed as a single, continuous mass; for example, a monolithic concrete slab is poured in one operation rather than in separate placements.

Mortar

A workable paste of cement, lime, sand, and water that hardens to bond masonry units together, fill joints, and provide a weather-resistant barrier.

Mortise

A rectangular cavity cut into a piece of wood or metal to receive a corresponding tenon or hardware component such as a lock or hinge.

Mudsill

The lowest sill plate of a framed structure, anchored to the foundation and providing the base for the entire wall and floor framing above.

Mullion

A vertical structural member between two window or door units in a single opening, joining and supporting the individual frames within the rough opening.

Muntin

A narrow strip of wood or metal separating and holding individual panes of glass within a window sash; also called a muntin bar or grille.

Muntin Bar

A thin divider bar within a single window sash, holding separate panes of glass or simulating divided light in a single insulated glass unit.

Mushroom

A structural column design where the top of the column flares outward to support a flat slab without beams; also a type of high-strength anchor.

Mute

A sound-dampening device or treatment, such as acoustic panels or pads, installed to reduce noise transmission between rooms or through ductwork.

Manning Formula

An empirical equation for calculating the flow velocity and capacity of open channels, culverts, and pipes based on roughness, slope, and hydraulic radius.

Mansard

A roof style with two slopes on all four sides; the lower slope is steeper, often nearly vertical, providing maximum usable attic floor area.

Masonry Cement

A blended cement primarily used for mortar and stucco, containing Portland cement, limestone, and additives for workability and water retention.

Mat Foundation

A thick, heavily reinforced concrete slab covering the entire building footprint, distributing loads when soil bearing capacity is low; also called raft foundation.

Metal Stud

A cold-formed steel C-shaped channel used in place of wood studs for interior partition walls in commercial and some residential construction.

Meter

A device that measures and records consumption of a utility such as electricity, gas, or water for billing purposes by the utility provider.

Microlam

A brand name for laminated veneer lumber (LVL) used as beams and headers, known for high strength and dimensional consistency across long spans.

Mil

A unit of thickness equal to one-thousandth of an inch (0.001"), used to specify the thickness of plastic sheeting, coatings, and vapor barriers.

Mill

A manufacturing facility that processes raw materials into finished products; in lumber, a sawmill converts logs into boards and dimensioned lumber.

Miter Saw

A power saw mounted on a pivoting arm that makes precise angled crosscuts in wood, trim, and molding; a fundamental finish carpentry tool.

N

Nailer

A framing member or strip secured to a structural surface to provide a solid nailing surface for finishes, roofing, or other attachments.

NEC

National Electrical Code; the standard for safe electrical installation in the US, updated every three years and adopted by most local jurisdictions.

Neutral Wire

The grounded current-carrying conductor in an AC circuit that completes the circuit back to the source; typically white or gray insulation.

Newel

The main vertical post at the bottom or top of a stair balustrade, anchoring the handrail and providing structural support for the entire railing system.

NFPA

National Fire Protection Association; an organization that publishes fire safety codes and standards including the National Electrical Code and Life Safety Code.

Niche

A recessed area in a wall used for display shelves, shower storage, or architectural accent; requires framed and finished enclosure in the wall cavity.

Nipple

A short length of threaded pipe used to connect two pipe fittings or to extend a plumbing connection a small distance.

NMC Cable

Non-Metallic Cable; electrical cable with a plastic sheathing containing insulated conductors and a ground wire; commonly called Romex for residential wiring.

Non-Bearing Wall

A wall that supports only its own weight; can be removed or altered without affecting the structural integrity of the building.

Nosing

The rounded or projecting front edge of a stair tread that extends beyond the riser below, providing additional walking surface and safety visibility.

Nozzle

A projecting spout or fitting at the end of a pipe, hose, or sprayer that directs and controls the flow pattern of liquid or gas.

Nail Pop

A defect in drywall where a nail or screw head becomes visible as a small bump or crack, caused by lumber shrinkage or fastener movement behind the surface.

Nail Set

A small punch-like tool with a cupped tip used to drive finish nail heads below the wood surface, allowing the depression to be filled for a smooth finish.

NEMA

National Electrical Manufacturers Association; an organization setting standards for electrical enclosures, motor ratings, and equipment configuration classifications.

Notch

A cut or indentation made in the edge of a framing member, joist, or stud, such as for plumbing pipes; limited by code to maintain structural integrity.

O

O.C. (On Center)

A measurement term meaning spacing from the center of one framing member to the center of the next, such as studs placed 16 inches O.C.

Oakum

Loosely twisted hemp or jute fiber, traditionally impregnated with pitch and packed into pipe joints to create a watertight seal in cast iron bell-and-spigot connections.

Obscure Glass

Translucent glass with a textured, frosted, or patterned surface that diffuses light while blocking clear visibility, used for bathroom windows and privacy panels.

Offset

A plumbing or duct configuration using two fittings to shift the line laterally while maintaining parallel flow; also any dimensional deviation from a reference line.

Ohm

The unit of electrical resistance; one ohm is the resistance through which one volt of potential difference drives one ampere of current.

Oil-Based

A paint or finish formulation using alkyd or natural oils as the binder; provides a hard, durable finish but with higher VOC emissions and slower drying than latex.

Open Web Joist

A fabricated steel or wood truss joist with top and bottom chords connected by diagonal webbing, allowing mechanical runs through the open spaces.

Orange Peel

A sprayed drywall texture with a fine, mottled finish resembling the surface of an orange, achieved by spraying thinned compound at varying air pressures.

Orbit

A circular path of motion; in construction hardware, a type of spring-loaded cabinet hinge that allows a door to open with a push-release mechanism.

O-Ring

A circular rubber or synthetic elastomer gasket with a round cross-section, seated in a groove to create a pressure-tight seal between two mating parts.

OSB

Oriented Strand Board; an engineered wood panel made of compressed wood strands arranged in cross-oriented layers bonded with resin, used for sheathing and subfloors.

Outlet

An electrical receptacle providing a point in a wiring system where current can be taken to supply lighting, appliances, or equipment.

Outside Corner

An external corner of a building or room trim; in drywall, a metal corner bead is used to protect and finish the 90-degree protruding edge.

Overhang

The portion of a roof or upper floor that extends beyond the exterior wall below, providing shade for windows and protection from rain for the wall surface.

Owner-Builder

A property owner who acts as their own general contractor, managing the construction process and assuming the legal responsibilities for the project.

Oxidation

A chemical reaction of a material with oxygen; in construction, causes rust on iron and steel, and discoloration or degradation of certain finishes and materials.

Ogee

An S-shaped molding profile with a convex curve flowing into a concave curve; commonly used in baseboard, crown molding, and decorative edge profiles.

Open Cell

A type of spray polyurethane foam insulation with a sponge-like structure that allows air and vapor permeability; lower density with good sound attenuation.

Organic

Naturally derived materials or compounds; in construction, refers to wood, natural fibers, and plant-based binders, which may be susceptible to rot and insect damage.

Overcurrent

Any electrical current exceeding the rated capacity of a conductor or equipment, which can cause overheating and fire; protected by fuses or circuit breakers.

P

Pad

A level, compacted, and prepared surface area for placing a concrete slab, building, or equipment; also the slab itself for an air conditioner condenser.

Paint

A liquid coating applied to surfaces for protection and decoration, consisting of pigment suspended in a binder or vehicle that cures to form a solid film.

Panel

A flat sheet of material such as plywood or drywall; also the electrical service panel, or a framed section of a wall, door, or cabinet.

Parapet

A low protective wall extending above the roofline at the edge of a flat or low-slope roof, often seen on commercial buildings and some residential styles.

Parge

A thin coat of mortar or cementitious material applied to masonry surfaces to smooth rough blocks, provide a finished appearance, or seal against moisture.

Particle Board

An engineered panel made of wood particles bonded with resin under heat and pressure; used for underlayment, cabinet cores, and furniture components.

Partition

An interior non-load-bearing wall dividing one space from another, typically framed with studs and finished with drywall or paneling.

Patching

The process of repairing holes, cracks, or surface defects in finish materials using compound, mortar, or patching plaster before final finishing.

Paver

A pre-cast concrete, brick, or natural stone unit used for creating exterior paved surfaces such as patios, walkways, and driveways with sand-filled joints.

PEX

Cross-linked polyethylene; a flexible plastic tubing widely used for residential hot and cold water supply lines, known for freeze resistance and ease of installation.

Picture Window

A large, fixed, non-operable window designed to frame a view, providing maximum daylight and unobstructed visibility without ventilation capability.

Pier

A vertical foundation element, typically a concrete cylinder or block column, supporting concentrated loads and transferring them to deeper bearing soil strata.

Pigtail

A short length of wire used to connect a device terminal to a circuit conductor inside an electrical box; also a flexible plumbing connector from a fixture to supply stop.

Pilaster

A shallow rectangular column projecting slightly from a wall surface, providing both decorative articulation and additional load-bearing capacity in masonry walls.

Pilot Hole

A small-diameter hole drilled into material before inserting a screw or nail, reducing the risk of splitting the workpiece and guiding the fastener.

Pitch

The slope of a roof expressed as the ratio of vertical rise to horizontal run, or the angle of inclination; also the presence of pine resin in wood.

Plane

A flat, two-dimensional surface, such as a wall plane or roof plane; also a hand tool with a sharp blade used to smooth and thin wood surfaces.

Plaster

A traditional interior finish material of cement, lime, or gypsum mixed with water and applied in layers over lath to create a hard, durable wall and ceiling surface.

Plate

A horizontal framing member at the top or bottom of a wall, such as the top plate connecting studs or the bottom plate anchored to the floor structure.

Plenum

An enclosed space in a building used for air circulation as part of the HVAC air distribution system, such as the cavity above a suspended ceiling used as a return air path.

Plinth

A square or rectangular base block at the bottom of a column, pilaster, or door casing; also a raised platform supporting a fixture or appliance.

Plumb

Perfectly vertical; determined using a spirit level or plumb bob and line. A critical alignment condition for framing, cabinetry, and structural elements.

Plumbing Stack

The main vertical pipe in a building's drain, waste, and vent system, extending through the roof to vent sewer gases and equalize air pressure.

Plywood

An engineered wood panel made by cross-laminating thin wood veneers with adhesive, producing a strong, stable sheet material for sheathing, subfloors, and finishing.

Pocket Door

A sliding door that disappears into a cavity within the adjacent wall when open, saving floor space compared to a traditional swinging door.

Point Load

A concentrated force applied at a single specific location on a structural member, as opposed to being distributed evenly along its length or area.

Polyurethane

A versatile polymer used as a durable clear coating for wood floors and furniture, a wood glue, and as spray foam insulation in two-component formulations.

Ponding

The accumulation of standing water on a flat or low-slope roof or paved surface, indicating improper drainage that can lead to premature material degradation.

Poplar

A lightweight, straight-grained hardwood commonly used for painted trim, molding, and interior applications where appearance-grade hardwood is not required.

Porch

A covered, exterior platform attached to a building entrance, often with a separate roof, railings, and columns; may be open-air or screened.

Portland Cement

The most common type of hydraulic cement, a fine powder made from heated limestone and clay; the primary binding ingredient in concrete and mortar.

Post

A vertical structural member, similar to a column but usually of wood, carrying loads from beams or girders down to the foundation or lower level.

Post-Tension

A concrete reinforcement method where high-strength steel tendons are tensioned after the concrete has hardened, applying compressive forces to increase strength and reduce cracking.

PPI

Pounds Per Inch; a unit used in structural specifications, such as the allowable load on a truss plate per inch of plate length measured perpendicular to the applied force.

Precast

Concrete elements that are cast and cured in a controlled factory environment before being transported to the job site for final installation and erection.

Pressure Treated

Lumber infused with chemical preservatives under pressure in a treatment vessel, protecting against rot, fungal decay, and insect attack in ground contact applications.

Primer

A preparatory coating applied before paint to improve adhesion, seal porous surfaces, block stains, and provide a uniform base for the topcoat color.

Projection

The distance a building element extends beyond its support or reference plane, such as the overhang of a cornice or the projecting dimension of a window sill.

PSI

Pounds per Square Inch; the standard unit of pressure or stress in the US, used in concrete strength, soil bearing capacity, plumbing systems, and pneumatic tools.

Purlin

A horizontal secondary structural member in a roof system, spanning between rafters or trusses to support the roof decking or sheathing.

PVC

Polyvinyl Chloride; a rigid white plastic widely used for plumbing drain pipes, electrical conduit, window frames, and exterior trim due to its durability and low cost.

Q

Quarter Round

A convex molding with a quarter-circle profile, used as shoe molding at the base of baseboards, inside corners, and trim transitions to conceal gaps.

Queen Post

A pair of vertical tension members in a truss connecting the bottom chord to the top chord, providing intermediate support and reducing required rafter size.

Quirk

A narrow, deep groove separating two adjacent moldings, typically found in bead-and-quirk or quirked baseboard profiles for shadow line definition.

Quoin

Large, prominent masonry blocks at the corner of a building, often projecting slightly and using contrasting material or finish for architectural emphasis.

Q-Decking

A brand of corrugated metal roof decking with dovetail-shaped ribs that mechanically bond to concrete fill in composite floor systems.

R

Rabbet

An L-shaped groove cut along the edge or end of a board to receive another piece and create a flush, interlocking corner or edge joint.

Racking

The lateral tilting or distortion of a frame or panel from its intended right-angle shape, typically caused by wind loads, door use, or inadequate bracing.

Radial Saw

A circular saw suspended from an overhead arm that can be pulled across the workpiece, used for crosscutting, ripping, and dadoing wide stock; also radial arm saw.

Radon

A naturally occurring radioactive gas that can seep from soil into buildings through foundation cracks; prolonged exposure is a leading cause of lung cancer in nonsmokers.

Rafter

An inclined structural member in a roof frame running from the ridge to the eave, supporting the roof sheathing, covering, and imposed loads.

Rail

A horizontal member of a framed assembly, such as the top and bottom of a cabinet door, a staircase balustrade, or a guardrail system.

Rake

The sloped edge of a gable roof at the end wall; the angled board or trim finishing this edge, also called the rake board or barge rafter.

Random Rubble

A stone masonry pattern built of irregular, uncut stones fitted together in a rough pattern without continuous horizontal courses, creating a rustic appearance.

Rebar

Steel reinforcing bar embedded in concrete to improve tensile and shear strength; typically deformed with ridges to bond mechanically with the surrounding concrete.

Receptacle

An electrical outlet into which a plug can be inserted to connect equipment or appliances to the building's wiring system; also called a convenience outlet.

Reducer

A pipe fitting that connects two pipes of different diameters; also a transition strip in flooring that bridges two surfaces of slightly different heights.

Reflector

A surface or device that redirects light, heat, or sound; used in lighting fixtures to direct output, behind radiators, and as insulation facing.

Register

A grille with an adjustable damper at the end of an HVAC duct, controlling the volume and direction of conditioned air entering a room; also called a supply register.

Reglet

A groove or slot cut into a masonry or concrete surface to receive flashing, anchor a termination bar, or create a shadow line reveal.

Reinforced Concrete

Concrete that contains embedded steel reinforcing bars, mesh, or fibers to withstand tension and shear forces; widely used in virtually all structural concrete applications.

Relieving Angle

A steel angle attached to the structural frame or wall to support the dead load of exterior masonry veneer at each floor level, relieving weight on the lower courses.

Resaw

To cut a thick board lengthwise into thinner pieces along the grain, typically using a bandsaw; used to produce book-matched veneers or thinner stock.

Resilient Channel

A flexible metal furring strip used to decouple drywall from framing, reducing sound transmission through walls and ceilings by breaking the vibration path.

Retaining Wall

A wall engineered to hold back soil or other loose material where a grade change is necessary; must resist the lateral pressure of the retained earth.

Return

The ductwork carrying air back from rooms to the HVAC air handler; also a short wall, railing, or molding section turning back toward a wall at an end point.

Reveal

The side surfaces of a door or window opening between the frame and the finished wall surface; also a deliberate gap between materials for shadow line effect.

Ridge

The highest horizontal line of a sloped roof, where two roof planes meet at the peak and rafters or trusses are joined together with a ridge board or beam.

Ridge Vent

A continuous ventilation opening along the roof peak, covered with a baffled cap that allows hot, humid attic air to exhaust while preventing rain and snow entry.

Rip

To cut lumber lengthwise along the grain; a rip cut runs parallel to the wood fibers, as opposed to a crosscut which runs perpendicular to the grain.

Riser

The vertical face of a stair step connecting one tread to the next; also a vertical plumbing pipe, electrical conduit run, or HVAC duct riser between floors.

Romex

A brand name commonly used generically for non-metallic sheathed electrical cable (NMC) used in residential wiring, with plastic jacket containing multiple conductors.

Roof Pitch

The steepness of a roof expressed as a ratio of vertical rise to horizontal run; a 4:12 pitch rises 4 inches for every 12 inches of horizontal run.

Rough Opening

The framed opening in a wall into which a window or door unit is installed; larger than the unit dimensions to allow for shimming, leveling, and insulation.

Rough-in

The first phase of installing mechanical, electrical, and plumbing systems, including running wires, pipes, and ducts before insulation and drywall are installed.

Rout

To cut a groove, profile, or cavity in wood or other material using a router; essential for joinery, edge profiling, hinge mortising, and decorative inlay.

Rowlock

A brick laid on its face edge with the end visible in the wall face, often used as a cap course or for decorative banding in brick masonry.

R-Value

A measure of thermal resistance; the higher the R-value, the better a material insulates by resisting heat flow through conduction, convection, and radiation.

Rabbeted

Having a rabbet cut into the edge or face; describes a joint, casing, or door jamb where one piece overlaps and interlocks with the adjoining surface.

Radial Arm Saw

A stationary power saw with a motor and blade on a horizontal arm that can be lowered and pulled across the workpiece for crosscuts and dados.

Rafter Tail

The exposed end of a rafter that projects beyond the exterior wall to form the eave overhang; often left exposed for decorative effect in craftsman style.

Rain Screen

An exterior cladding system with a ventilated air cavity behind the siding, allowing moisture to drain and dry while equalizing pressure to reduce water intrusion.

Rake Board

The trim board running along the sloped edge of a gable roof from the eave to the ridge, covering the exposed ends of the roof sheathing and fascia.

Ranch

A single-story residential architectural style characterized by a long, low profile, open floor plan, and attached garage; popular in mid-century American suburbs.

Random Width

Flooring boards of varying widths installed in a deliberate, non-uniform pattern, often used with reclaimed, rustic, or wide plank hardwood installations.

Relief Valve

A safety device on a water heater or pressure vessel that automatically opens to release excess pressure or temperature, preventing tank rupture or explosion.

Rough Carpentry

The structural wood framing phase of construction, including framing of walls, floors, and roofs before mechanical trades and finish carpentry begin.

S

Saddle

A small gable-like roof structure built behind a chimney where it intersects a sloped roof to divert water around the chimney; also called a cricket.

Safety Glass

Glass processed to reduce injury risk when broken; includes tempered glass that crumbles into small granules and laminated glass held together by an interlayer.

Sanding

The process of smoothing a surface with abrasive paper, progressively reducing grit size, to prepare wood, drywall compound, or metal for finishing.

Sanitary Sewer

The underground pipe system carrying wastewater from plumbing fixtures to a municipal treatment plant or private septic system; separate from storm drainage.

Sash

The movable or fixed frame in a window holding the glass panes; a double-hung window has an upper and lower sash that slide vertically.

Saturated Felt

Heavy paper impregnated with asphalt and used as an underlayment layer beneath roofing shingles or siding to provide secondary moisture protection.

Scaffold

A temporary elevated platform and structure used to support workers, tools, and materials during construction, repair, or maintenance activities above ground level.

Scale

The proportional relationship between a drawing dimension and the actual dimension it represents; also a mineral deposit buildup inside pipes and on plumbing fixtures.

Scarf Joint

A joint where two pieces are cut at complementary angles and overlapped to create a longer continuous member, used in trim, flooring, and timber framing.

Schedule

A table of specifications on plans listing items such as doors, windows, and finishes with quantities, sizes, and types; also pipe wall thickness classification.

Scratch Coat

The first rough coat of plaster or stucco applied to lath, deliberately scored with horizontal scratches to provide a mechanical key for the next coat.

Screed

A straightedge board or tool pulled across freshly placed concrete to level it to the correct elevation; also a thin mortar layer for leveling floors.

Scupper

An opening through a parapet, curb, or edge of a flat roof that allows water to drain off the roof into a downspout or conductor head.

Sealant

A flexible material applied in a joint to prevent the passage of air and water while accommodating movement; includes caulk, silicone, and polyurethane products.

Sealer

A penetrating liquid applied to porous surfaces such as concrete, stone, or grout to reduce absorption of water, stains, and contaminants.

Seasoning

The process of drying lumber to reduce its moisture content to a level suitable for use in construction; may be done by air drying or kiln drying.

Seismic

Relating to earthquakes or earth vibrations; seismic design involves engineering structures to withstand ground motions without collapse and minimize damage.

Self-Leveling

A fluid cement-based compound that flows and settles to a smooth, flat surface under gravity, used to level uneven concrete or subfloors before finished flooring.

Septic

A private underground wastewater treatment system using a tank for solids settling and decomposition, and a drain field for effluent absorption into soil.

Service Entrance

The point where the utility's electrical conductors enter a building, including the meter, main disconnect, and the path to the electrical panel.

Setback

The minimum required distance between a building or structure and the property line, road, water body, or another structure as mandated by zoning regulations.

Settlement

The downward movement of a building or foundation due to soil compression under load, potentially causing cracks, sticking doors, and structural distress.

Sewer

The underground pipe network that conveys wastewater and sewage from buildings to a centralized treatment facility or to a private on-site disposal system.

Shake

A thick, hand-split or rough-sawn wood roofing shingle, usually cedar, with a heavily textured surface providing a rustic appearance; also a separation crack along the wood grain.

Shear

A force causing adjacent parts of a material to slide past one another in opposite directions; a fundamental structural stress condition resisted by shear walls.

Sheathing

The structural panel material, typically plywood or OSB, attached to the exterior face of studs or roof framing, providing a base for cladding or roofing and resisting lateral loads.

Shed Roof

A single-slope roof plane angled in one direction only, typically attached to a taller adjacent wall; also called a skillion, lean-to, or mono-pitch roof.

Shiplap

Boards with a rabbeted overlap joint along the edges, allowing them to interlock with a small gap or reveal between courses; popular for interior accent walls.

Shoring

Temporary structural supports erected to hold up walls, floors, or excavations during construction, demolition, or underpinning activities for safety.

Sill

The bottom horizontal member of a window or door frame, sloped to shed water; also the lowest framing member resting on the foundation, called the mudsill.

Silt

Fine granular soil particles between clay and sand in size; tends to hold water, compacts poorly, and may require stabilization or removal beneath foundations.

Single-Hung

A window with only the lower sash operable; the upper sash is fixed in place. Similar in appearance to double-hung but only bottom ventilation.

Sister

To attach a new framing member alongside an existing one to reinforce, strengthen, or straighten it; commonly done to repair damaged or undersized floor joists and rafters.

Site Plan

A scaled drawing showing the building footprint, property boundaries, access, landscaping, drainage, and utility connections in relation to the overall lot.

Skewback

The angled bearing surface at the end of an arch where it meets the supporting abutment or pier, designed to receive the inclined thrust of the arch.

Skim Coat

A thin finish layer of joint compound or plaster applied over an entire wall or ceiling to create a smooth, even surface by filling minor imperfections.

Slab

A flat, horizontal concrete floor or foundation poured directly on the ground or suspended as a structural floor deck; may be reinforced with steel.

Slag

A stony byproduct of the smelting process sometimes used as lightweight aggregate in concrete or as mineral fiber for insulation products.

Sleeper

A horizontal wood member laid on a concrete slab or subfloor to provide a nailing base for finish flooring, or a timber laid on the ground for support.

Sleeve

A pipe or tube cast into a concrete wall or floor to create a passage for pipes, ducts, or cables through the structure; also a protective casing.

Slump

A measure of concrete workability determined by the amount a truncated cone of fresh concrete sags or spreads after the mold is removed; a standard quality control test.

Soffit

The finished underside surface of the eave overhang, connecting the exterior wall to the fascia; also the underside of roof overhangs, archways, and beam projections.

Soil Stack

A vertical plumbing pipe carrying waste from toilets and other sanitary fixtures down to the building drain; extends upward as a vent through the roof.

Sole Plate

The bottom horizontal member of a framed wall fastened to the floor; synonymous with bottom plate in light frame wood construction.

Sound Transmission

The passage of airborne or impact-generated sound energy through building assemblies; rated by STC and IIC classifications in acoustic design.

T

T&G (Tongue and Groove)

A joint system where a protruding tongue on one board fits into a matching groove on the adjacent board, creating a tight, self-aligning connection commonly used in flooring and paneling.

Tack Cloth

A sticky cheesecloth impregnated with a tacky resin, used to wipe down surfaces and remove fine dust particles before painting or finishing for a smooth result.

Tail Beam

A shortened floor joist running from a header around an opening to the supporting girder or bearing wall, as used around stair openings or chimneys.

Taper

A drywall finishing specialist who applies joint tape and compound to seams, corners, and fasteners; also a gradual reduction in thickness or width of a member.

Tempered Glass

Safety glass heat-treated to increase strength; when broken, it crumbles into small granular pieces rather than sharp shards, required in doors, sidelights, and wet areas.

Template

A rigid pattern or guide used to trace or transfer the exact shape and dimensions of a workpiece onto material for cutting, drilling, or routing.

Tendon

A high-strength steel cable or strand in a post-tensioned or pre-tensioned concrete member, placed in a duct and stressed to compress the surrounding concrete.

Termite Shield

A metal barrier installed between the top of a foundation and the wood sill plate, with projecting edges that prevent termites from reaching wood undetected.

Terrazzo

A polished flooring finish composed of marble or granite chips embedded in a cement or epoxy binder, ground smooth, and sealed for a decorative durable surface.

Thermal Break

A low-conductivity material inserted within a metal frame or assembly that interrupts the path of heat flow, improving the overall thermal performance of windows and doors.

Thermocouple

A safety sensor in a gas appliance that generates a small electric voltage when heated by a pilot flame, holding open the gas valve; if the flame goes out, the valve closes.

Three-Way Switch

An electrical switching arrangement using two switches to control a single light fixture from two separate locations, such as at the top and bottom of a stairway.

Threshold

A strip at the bottom of an exterior door opening bridging the gap between the floor and the door bottom, weatherproofing the transition and minimizing air infiltration.

Thru-Wall Flashing

A flashing installed completely through a masonry wall projecting from both faces, intercepting downward-moving moisture and directing it to the exterior via weep holes.

Tie

A connecting element used to bind two parts together; in masonry, a metal strip connecting wythes; in concrete formwork, a rod holding forms apart under pour pressure.

Tilt-Up

A method of concrete construction where wall panels are cast horizontally on the floor slab, then lifted by crane and secured into vertical position.

Toe Kick

The recessed space at the bottom of a base cabinet below the door front, allowing a person to stand close to the countertop without hitting their toes.

Toenail

To drive a nail at an angle through the edge or end of one board into another, joining framing members such as stud to plate or rafter to top plate.

Top Plate

The uppermost horizontal member of a framed wall running along the top of the studs, typically doubled, tying walls together and supporting joists, rafters, or trusses.

Torque

A rotational or twisting force applied to a fastener, shaft, or structural member; measured in foot-pounds or inch-pounds for tightening bolts and lag screws.

Trap

A U-shaped or curved section of drain pipe beneath a plumbing fixture that holds a water seal, preventing sewer gases from entering the building while allowing waste flow.

Tread

The horizontal upper surface of a stair step on which a person walks; building codes specify minimum tread depth for safety and comfortable stair ascent and descent.

Trimmer

A framing member supporting a header at an opening; in a floor, the shortened joist running parallel to main joists around an opening and supported by headers.

Truss

A prefabricated triangular structural framework of chords and webs used to span long distances economically, replacing individual rafters and ceiling joists in roof construction.

Turnbuckle

A mechanical coupling with opposing left-hand and right-hand threaded ends, adjusted by rotating the central body to tighten or loosen connected cables and rods.

U

U-Factor

A measure of thermal transmittance; the rate of heat transfer through a building assembly, expressed in BTUs per hour per square foot per degree Fahrenheit. A lower U-factor means better insulation.

UL Listed

Underwriters Laboratories certification indicating a product has been tested and meets recognized safety standards for its intended use and is monitored for ongoing compliance.

Underlayment

A layer of material, such as plywood or felt paper, installed under the finish floor or roofing to provide a smooth, stable, and moisture-resistant base.

Union

A three-piece threaded pipe fitting that joins two pipes in a way that allows disconnection without cutting, using a central nut to draw the ends tightly together.

Uplift

The upward force on a roof or structure caused by wind flowing over and creating negative pressure; resisted by hold-downs, straps, and proper anchoring to the foundation.

Urethane

A family of polymers used in tough, abrasion-resistant coatings, adhesives, and expanding foams; valued for flexibility, durability, and strong bonding to various substrates.

Utility Easement

A legal right granted to a utility company or municipality to access and use a portion of private property for installing and maintaining infrastructure such as power lines or pipes.

UV

Ultraviolet radiation from the sun; prolonged UV exposure degrades many building materials, including plastics, wood finishes, and roofing membranes, requiring protective measures.

U-Channel

A structural channel-shaped metal section with a U-shaped cross-section, used for framing, edging, and track systems in both structural and finish applications.

Undercut

To cut away the bottom edge of a door or trim to clear a finished floor surface; also a metal removal process in welding preparation creating a grooved edge.

V

Valley

The internal angle formed where two intersecting roof slopes meet, directing a large volume of runoff water to the eaves and requiring reinforced flashing or metal lining.

Vapor Barrier

A material with very low permeability that retards the passage of water vapor, preventing condensation within wall and roof assemblies in cold climates.

Vapor Retarder

A material that slows moisture vapor diffusion but is not completely impermeable; classified by permeance ratings for use in different climate zones and wall configurations.

Veneer

A thin layer of decorative material bonded to a substrate for appearance; includes wood veneer on plywood, brick veneer on framing, and stone veneer for facades.

Vent

An opening or pipe that allows air circulation, exhausts combustion gases, or equalizes pressure in a plumbing drainage system to allow proper flow and prevent siphonage.

Vent Stack

A vertical vent pipe serving multiple plumbing fixtures, extending through the roof and connecting to the main vent of the building's drain, waste, and vent system.

Vermiculite

A lightweight, fire-resistant, expanded mineral used for loose-fill attic insulation and as an aggregate in lightweight plasters; some older vermiculite may contain asbestos contamination.

Vertical Grain

Lumber sawn with growth rings oriented roughly perpendicular to the wide face, producing a straight, uniform grain pattern with excellent dimensional stability.

Vestibule

A small entrance hall or anteroom between the exterior door and the interior of a building, creating an airlock that reduces heat loss and drafts upon entry.

Viscosity

A fluid's resistance to flow; in construction, affects paint application, concrete workability, caulk gunnability, and adhesive spread with higher viscosity materials being thicker and less pourable.

Volatile

Easily evaporated at normal temperatures; volatile organic compounds in paints, adhesives, and finishes contribute to indoor air quality concerns and smog formation.

Volt

The unit of electrical potential difference; standard residential service in the US is 120/240 volts, driving current through circuits to power equipment and lighting.

Voltage Drop

The reduction in voltage along a conductor carrying current, proportional to the wire length and current magnitude; limited by code to ensure equipment performs properly.

V-Joint

A decorative groove or channel with a V-shaped profile cut at the junction of two boards or milled into a single board face, common in tongue-and-groove paneling.

Vaulted Ceiling

A ceiling that follows the underside of the roof slope rather than being flat, creating a sense of height and openness in rooms, often with exposed beams.

W

Wainscot

A protective and decorative wall treatment, typically wood paneling or beadboard, covering the lower portion of an interior wall from floor to chair rail height.

Waferboard

An engineered wood panel similar to OSB, made of large wood wafers bonded with resin; historically an early form of oriented strand board now largely superseded.

Wall Plate

The top or bottom horizontal framing member in a wall; the bottom plate anchors to the floor, and the top plate (often doubled) ties the studs together.

Warp

Distortion of lumber from its original flat shape due to uneven drying, moisture changes, or internal stresses; includes cupping, bowing, twisting, and crooking.

Waste Stack

The vertical pipe in a plumbing system that conveys wastewater from sinks, tubs, and other non-toilet fixtures downward to the building drain and sewer.

Water Ceiling

A level at which underground water saturates all available voids; in excavation, it refers to the water table depth that affects dewatering and foundation design.

Water Hammer

A loud knocking or banging noise in plumbing pipes caused by a hydraulic pressure surge when a valve closes abruptly, rapidly stopping the flow of incompressible water.

Waterproofing

The treatment or covering of a surface to make it completely impervious to liquid water under hydrostatic pressure, typically used on below-grade foundations and wet areas.

Wattle

Interwoven sticks or twigs forming a framework for walls in traditional earth construction, historically daubed with mud plaster; also a sediment control product made of straw.

Weep Hole

A small opening left at the base of a masonry veneer wall or at the bottom of a retaining wall to allow accumulated moisture to drain out of the wall cavity.

Weir

A low dam or raised structure across a channel that controls water flow and provides a means of measuring discharge volume passing over it in drainage calculations.

Weld

The fusion of two metal pieces by heating the joint to melting point, often with added filler material, creating a strong, continuous, load-transferring structural connection.

Whole House Fan

A large exhaust fan installed in an attic ceiling that draws cool outside air through open windows and pushes hot indoor air out through attic vents for cooling without air conditioning.

Wind Bracing

Structural elements, such as diagonal straps, shear panels, or portal frames, installed in walls and roofs to transfer wind loads safely to the foundation.

Window Sash

The framework surrounding the glass in a window; may be fixed in place or movable within the window frame, supporting the glass and weatherstripping.

Wing Wall

A short wall extending outward from a structure, such as at the end of a foundation retaining wall or bridge abutment, for lateral support and erosion protection.

Wire Gauge

A standardized numerical system for specifying the diameter of electrical wire; lower gauge numbers indicate thicker wire capable of carrying more current safely.

Witness Hole

A small pilot hole drilled to mark a position or indicate the correct depth for subsequent operations; used in aligning dowels or verifying blind depth in drilling.

Wood Putty

A dense, pigmented filler paste used to fill nail holes, cracks, and small imperfections in finished wood surfaces after staining and before topcoating.

Wythe

A single vertical layer of masonry units in a wall; a solid brick wall or cavity wall may consist of one or multiple wythes tied together for structural action.

X

X-Acto

A brand of precision hobby knife with replaceable fine-point blades, widely used in model making, craft work, and detailed cutting of thin construction materials.

X-Brace

Diagonal cross bracing forming an X pattern between two vertical or horizontal members, providing exceptional lateral stiffness and load distribution in walls, trusses, and scaffolding.

X-Ray

A nondestructive testing method using penetrating electromagnetic radiation to inspect welds, concrete, and hidden structural elements for internal voids, cracks, or defects.

Y

Yard

A unit of length equal to 3 feet or 36 inches; also a cubic yard as a volume measure for concrete, aggregate, and excavation quantities in construction.

Yoke

A connecting framework that couples multiple components together; in electrical work, the metal mounting strap on a switch or receptacle that attaches it to the electrical box.

Y-Connector

A plumbing drain fitting shaped like the letter Y, allowing a branch line to join a main horizontal drain at a 45-degree angle for smoother waste flow compared to a tee.

Z

Z-Bar

A metal trim piece with a Z-shaped cross-section used as flashing between building components, such as at the intersection of vertical siding and horizontal trim or roof to wall transitions.

Z-Flashing

A Z-shaped metal flashing profile that directs water away from horizontal joints in siding and where dissimilar materials meet, preventing moisture penetration behind cladding.

Zoning

Municipal regulations that divide a jurisdiction into districts with specific land use, height, setback, and density requirements governing what can be built where.